[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [ARSCLIST] Tape transport gentleness was delicacy WAS reel choices was help in fair pricing of reel to reel machines
Not only do I agree, but I consider it as essential as getting a blood test
before an operation. I suspect many of us have compiled many unrecompensed
studio hours because, though the client may not be wiling to pay for this
phase of the work, that which follows it cannot be successfully accomplished
otherwise.
Steve Smolian
----- Original Message -----
From: "Kiwi O'Connell" <kiwioconnell@xxxxxxxxxxxxxxxx>
To: <ARSCLIST@xxxxxxxxxxxx>
Sent: Monday, January 29, 2007 9:52 PM
Subject: Re: [ARSCLIST] Tape transport gentleness was delicacy WAS reel
choices was help in fair pricing of reel to reel machines
Hi -
To me, it is well worth the effort for the benefit of the clients and
expensive head stacks, to take the time and effort to triage the tapes
first, especially when it IS obvious that there are splices, and possibly
SSS.
I had a tape the other day which I knew had a potential of 34 splices, but
in actual fact it turned out to have 49 badly done splices and 3 pieces of
splicing tape which had ripped off the oxide layer leaving holes in the tape
itself. Some of these splices snapped during the triage process, which I
knew they would do, others were just plan stubborn! Not to mention the
gooey glue residue. Plus, this tape required baking.
Is it not cheaper in the long run for the client to have the triage process
done before the attempted transfer rather than have to stop and start the
load-in every time a splice lets go during the transfer process?
Can you charge the client for the damage done to the heads (i.e. Head Clogs)
or the cost of replacement heads if the tape has not been properly triaged
and repaired in the first place?
I realize some clients may not have a lot of money, but I also know that all
clients "claim" their audio is very important to them and invaluable but at
the end of the day, they couldn't give damn about the actual asset itself. I
hear "I don't care about the tape, just what's on it" too many times.
I find that very sad, as that is the original treasure.
Cheers
Marie
Marie O'Connell
Sound Archivist/Audio Engineer/Sound Consultant
3017 Nebraska Avenue
Santa Monica, CA, 90404
Ph: 310-453-1615
Fax: 310-453-1715
Mobile: 601-329-6911
www.cupsnstrings.com
-----Original Message-----
From: Association for Recorded Sound Discussion List
[mailto:ARSCLIST@xxxxxxx] On Behalf Of Steve Puntolillo
Sent: Saturday, January 27, 2007 6:46 PM
To: ARSCLIST@xxxxxxxxxxxxxxxx
Subject: Re: [ARSCLIST] Tape transport gentleness was delicacy WAS reel
choices was help in fair pricing of reel to reel machines
Hi --
I had written:
>I should mention that the truly lovely Studer A820 1/4 and
1/2" machine
>(which is the *other* darling of mastering decks) can also
lose control
>of its tension sensing mechanism and "lose it's mind". I have not
>experienced this first hand, but have heard so from reliable
sources who
>own and love these machines.
>
>A possible advantage of the Studer is that it has a pinch
roller and so
>at least will power its way through tapes with little bits
of residual
>SSS without changing pitch. The ATR100 has no mechanism to combat
>temporary speed fluctuations due to tape that sticks or drags.
And Richard Hess answered:
I think Parker Dinkens might be able to shed further light on this
particular item (see I keep bringing everyone into this thread) as he
has now owned two A820s. One, sadly, was damaged beyond repair by
Katrina, but he has located a replacement and now has it.
Fortunately, all of his head blocks were saved.
See a later post for Parker's enlightening answer as well as a very nice
testimonial to Studer and the A820.
Richard continued:
Also, this _may_ be the reason that Mark Donahue uses A80 transports
for his work--Steve, I know that you are very pleased with yours for
tapes with bad splices.
Mark has indeed been kind enough to encourage me to put an A80RC here to
good use. ( http://www.sonicraft.com/a2dx.html#2T -- scroll down a bit
).
Not everyone has the budget to properly repair tapes with sticky
splices. Especially, when there are upwards of (70) 15 ips 10.5" reels
literally *riddled* with them. We had such a job come in and we ended up
evaluating a few machines to decide which to use.
In another post Scott Phillips wrote:
I would think the APR series would behave themselves pretty well under
these conditions...
We tried this job on an APR-5000 first. As expected, this machine got
very high marks for its gentleness. The jog shuttle allowed us to FF and
RW at a low speed, which is a big plus with challenged tapes. It also
sounds very nice. However, splices snagging on static surfaces in the
tape path were audible.
The Technics RS1500 (same model that Tom Fine likes) is really a
terrific little machine for anyone on a budget. It did the absolute best
job of playing the tapes without dropouts from the splices. This, we
felt, was an advantage of its IsoLoop tape path. We could see the supply
reel bounce as sticky splices let go of the layer of tape underneath.
Yet never did we *hear* the bounce in the transfer. And, its constant
tension FF & RW was gentle enough that we felt relatively (although not
completely) comfortable. We didn't feel that it sounded outstanding, but
certainly very respectable.
The Studer A80RC is very gentle on tape, although perhaps not quite as
gentle as the APR-5000. We were pleasantly surprised at how well it
handled the sticky splices -- almost as well as the Technics. It has
adjustable FF/RW speed and we felt very secure slowly shuttling tapes
whenever necessary. And, this particular model of A80, with it's second
generation class A discrete transistor playback amps, sounds very nice.
Using the Studer meant that we'd have to eat the cost of fixing the
occasional splice-related glitch that made it past the machine's
transport. But, great sound wins out here and we decided to use the
Studer instead of the Technics for this particular job.
Hope this info helps someone.
Best,
-- Steve
========================================================
Steve Puntolillo
Sonicraft A2DX Lab - Ultimate A_nalog 2 D_igital X_fers
http://www.sonicraft.com/a2dx
========================================================
--
No virus found in this incoming message.
Checked by AVG Free Edition.
Version: 7.5.432 / Virus Database: 268.17.14/657 - Release Date: 1/29/2007
9:04 AM